|
Basic oxygen steelmaking (BOS, BOP, BOF, and OSM), also known as Linz-Donawitz- steelmaking or the oxygen converter process〔Brock and Elzinga, p. 50.〕 is a method of primary steelmaking in which carbon-rich molten pig iron is made into steel. Blowing oxygen through molten pig iron lowers the carbon content of the alloy and changes it into low-carbon steel. The process is known as ''basic'' because fluxes of burnt lime or dolomite, which are chemical bases, are added to promote the removal of impurities and protect the lining of the converter.〔(''Basic Oxygen Steelmaking Simulation, version 1.36 User Guide'' ), steeluniversity.org, accessed 2014-05-24〕 The process was developed in 1948 by Robert Durrer and commercialized in 1952–1953 by Austrian VOEST and ÖAMG. The LD converter, named after the Austrian towns Linz and Donawitz (a district of Leoben) is a refined version of the Bessemer converter where blowing of air is replaced with blowing oxygen. It reduced capital cost of the plants, time of smelting, and increased labor productivity. Between 1920 and 2000, labor requirements in the industry decreased by a factor of 1,000, from more than 3 worker-hours per tonne to just 0.003.〔Smil, p. 99.〕 The vast majority of steel manufactured in the world is produced using the basic oxygen furnace; in 2000, it accounted for 60% of global steel output.〔 Modern furnaces will take a charge of iron of up to 350 tons and convert it into steel in less than 40 minutes, compared to 10–12 hours in an open hearth furnace. ==History== The basic oxygen process developed outside of traditional "big steel" environment. It was developed and refined by a single man, Swiss engineer Robert Durrer, and commercialized by two small steel companies in allied-occupied Austria, which had not yet recovered from the destruction of World War II.〔 In 1856, Henry Bessemer patented a steelmaking process involving oxygen blowing for decarburizing molten iron (UK Patent No. 2207).〔Smil, p. 97.〕 For nearly a hundred years commercial quantities of oxygen were not available at all or were too expensive, and the invention remained unused.〔 During World War II German (C. V. Schwartz), Belgian (John Miles) and Swiss (Durrer and Heinrich Heilbrugge) engineers proposed their versions of oxygen-blown steelmaking, but only Durrer and Heilbrugge brought it to mass-scale production.〔 In 1943, Durrer, formerly a professor at the Berlin Institute of Technology, returned to Switzerland and accepted a seat on the board of Roll AG, the country's largest steel mill.〔 In 1947 he purchased the first small 2.5-ton experimental converter from the U. S., and on April 3, 1948 the new converter produced its first steel.〔 The new process could conveniently process large amounts of scrap metal with only a small proportion of primary metal necessary.〔 In the summer of 1948 Roll AG and two Austrian state-owned companies, VOEST and ÖAMG, agreed to commercialize the Durrer process.〔Smil, pp. 97-98.〕 By June 1949, VOEST developed an adaptation of Durrer's process, known as the LD (Linz-Donawitz) process.〔Tweraser, p. 313.〕〔Smil, p. 98.〕 In December 1949, VOEST and ÖAMG committed to building their first 30-ton oxygen converters.〔 They were put into operation in November 1952 (VOEST in Linz) and May 1953 (ÖAMG, Donawitz)〔 and temporarily became the leading edge of the world's steelmaking, causing a surge in steel-related research.〔Brock and Elzinga, p. 39.〕 Thirty-four thousand businesspeople and engineers visited the VOEST converter by 1963.〔 The LD process reduced processing time and capital costs per ton of steel, contributing to the competitive advantage of Austrian steel.〔 VOEST eventually acquired the rights to market the new technology.〔 However, errors made by the VOEST and the ÖAMG management in licensing their technology made control over its adoption in Japan impossible and by the end of the 1950s the Austrians lost their competitive edge.〔 The original LD process consisted in blowing oxygen over the top of the molten iron through the water-cooled nozzle of a vertical lance. In the 1960s steelmakers introduced bottom-blown converters and introduced inert gas blowing for stirring the molten metal and removing the phosphorus impurities.〔 In the Soviet Union, some experimental production of steel using the process was done in 1934, but industrial use was hampered by lack of efficient technology to produce liquid oxygen. In 1939, the Russian physicist Pyotr Kapitsa perfected the design of the centrifugal turboexpander. The process was put to use in 1942-1944. Most turboexpanders in industrial use since then have been based on Kapitsa's design and centrifugal turboexpanders have taken over almost 100 percent of the industrial gas liquefaction and in particular the production of liquid oxygen for steelmaking. The big American steelmakers caught up late with the new technology; the first oxygen converters in the United States were launched at the end of 1954 by McLouth Steel in Trenton, Michigan, which accounted for less than 1 per cent of the national steel market.〔Smil, p. 99.〕 U.S. Steel and Bethlehem Steel introduced the oxygen process only in 1964.〔 By 1970 half of world's and 80% of Japan's steel output was produced in oxygen converters.〔 In the last quarter of the 20th century basic oxygen converters were gradually replaced by the electric arc furnace. In Japan the share of LD process decreased from 80% in 1970 to 70% in 2000; worldwide share of the basic oxygen process stabilized at 60%.〔 抄文引用元・出典: フリー百科事典『 ウィキペディア（Wikipedia）』 ■ウィキペディアで「Basic oxygen steelmaking」の詳細全文を読む スポンサード リンク
|